EGW Viper/Venom Ruger PC Carbine Sight Mount

Mounting Hardware is Included

This Mount Fits:
Camp Carbine 9mm (does not fit the early models, the hole spacing is different)
Camp Carbine 45
Glenfield 30
Henry Big Boy (H006)
Henry 3030 (H009)
Henry 4570 (H010)
Henry Big Boy (H012)
Henry Long Ranger (H014)
Henry .410 (H018) Only fits the 20" Barrel
Henry Side Gate Lever Action (H024)
Henry Long Ranger
Marlin 1895
Marlin 1894
Marlin 336
Marlin 375
Marlin 444
Marlin Model 36
Ruger PC Carbine*

*This mount only works with the Ruger PC Carbines that do not have the AR style handguard.

We have found that the included screws may need to be shortened due to dimensional differences in receivers.

Mounting Hardware is Included

This Mount Fits:
Camp Carbine 9mm (does not fit the early models, the hole spacing is different)
Camp Carbine 45
Glenfield 30
Henry Big Boy (H006)
Henry 3030 (H009)
Henry 4570 (H010)
Henry Big Boy (H012)
Henry Long Ranger (H014)
Henry .410 (H018) Only fits the 20" Barrel
Henry Side Gate Lever Action (H024)
Henry Long Ranger
Marlin 1895
Marlin 1894
Marlin 336
Marlin 375
Marlin 444
Marlin Model 36
Ruger PC Carbine*

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs

Mounting Hardware:
(2) 6-32 Button Head Screws
(2) 6-32 Flat Head Screws
(2) 6-48 Torx Head Screws
(2) 8-40 x .313" Torx Head Screws
(2) 8-40 x .330" Torx Head Screws

Red Dot Fitment:
Vortex Viper
Vortex Venom
Burris Fast Fire 1, 2, 3, 4
Docter
ADE RD3-001
ADE RD3-002
ADE RD3-009
UTG Reflex Micro Dot
Crimson Trace CTS-1200
Crimson Trace CTS-1300
Sightmark Mini Shot

The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.

*All ADE mounts require 6-32 x 3/8" screws.

Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.