EGW Viper/Venom Novak Sight Mount

Mounting Hardware is Included

This mount fits (including but not limited to):
Firearms with a traditional Novak cut rear sight.

Please note, some manufacturers use licensed Novak rear sights. These are cut to the manufacturer's spec and are NOT GENUINE/traditional/true Novak rear sight cuts. One of the most common manufacturers to do this is Taurus. Ruger also uses smaller Novak rear sights on their fixed sight revolvers. Our mount will NOT fit these applications since they are not a traditional/true Novak cut. We do not offer any options for those applications. Please refer to and/or call the manufacturer of your firearm to confirm that you have a GENUINE Novak cut, not a licensed Novak cut.

Please see our common 1911 dovetail chart if you are not sure which cut you have.

Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Minor modification may be neccessary for Rock Islands. Our products should be installed and checked by a qualified and competent gunsmith.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs

Mounting Hardware:
(2) 6-32 Button Head Screws
(2) 6-32 Flat Head Screws
(1) 6-32 Set Screw

Red Dot Fitment:
Vortex Viper
Vortex Venom
Burris Fast Fire 1, 2, 3, 4
Docter
ADE RD3-001
ADE RD3-002
ADE RD3-009
UTG Reflex Micro Dot
Crimson Trace CTS-1200
Crimson Trace CTS-1300
Sightmark Mini Shot

The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.

*All ADE mounts require 6-32 x 3/8" screws.

Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.

This mount fits (including but not limited to):
CZ 75 Bull Shadow
STI with fixed rear sights
STI Marauder
Christensen Arms 1911
Colt Delta Elite 10mm (2016 and newer)
Ruger SR 1911 (fixed rear sight)
Sig Sauer Nightmare
Citadel 1911s
Springfield Armory 1911 EMP - 9mm / .40
Springfield Armory 1911 EMP 4" Lightweight Champion - 9mm / .40
Springfield Armory 1911 EMP 4" Conceald Carry Contour Model - 9mm / .40
Springfield Armory 1911 Champion Operator Lightweight - .45
Springfield Armory 1911 Range Officer Compact - 9mm / .45
Springfield Armory 1911 Range Officer Champion - 9mm / .45
Springfield Armory 1911 Range Officer Elite Compact - 9mm / .45
Springfield Armory 1911 Range Officer Elite Champion - 9mm / .45
Springfield Armory 1911 Range Officer Elite Operator - 9mm / .45
Springfield Armory 1911 Loaded (Fixed Rear Sight) - .45
Springfield Armory 1911 TRP
Rock Island TCM Rock Standard MS HC Combo - 22TCM/9MMTCM
Rock Island TAC Ultra FS Combo - 22TCM/9MMTCM
Rock Island Rock Ultra FS Combo - 22TCM/9MMTCM
Rock Island TAC Ultra FS HC Combo - 22TCM/9MMTCM
Rock Island TAC Ultra MS HC Combo - 22TCM/9MMROCK
Rock Island Ultra CS-LTCM Rock Standard FS HC Combo - 22TCM/9MMROCK
Rock Island Ultra CCO
Rock Island TAC Ultra FS HC - 45 ACP
Rock Island TAC Standard FS - 45 ACP
Rock Island TAC Ultra FS HC - 9MM
Rock Island TAC Ultra FS - 45 ACP
Rock Island TAC Ultra CS - 45 ACP
Rock Island TAC Ultra CS - 9MM
Rock Island TAC Ultra FS - 10MM
Rock Island TAC Ultra MS - 10MM
Rock Island Rock Standard