EGW Viper/Venom SIG P220-229, 320 Sight Mount

Mounting Hardware is Included

This mount fits (including but not limited to):
Sig #8 Sights

P210A Standard
P220
P224
P225
P225-A1
P226
P227
P228
P229
P238
P239
P245
P320
P938
SP2022
M11-A1
MK25
Bersa Thunder UC Series (9/40/45)
Bersa Thunder HC Series (9/40/45)
FN 509

This mount does not fit:
Sig 1911s
Sig P220 10mm Hunter
Any Optics Ready Sigs i.e. P226 Legion RX, P229 RX, P320 X-Carry etc.
P210 Target
P365 (The dovetail cut is too deep to work with our mount)
FN 509 Tactical

This mount does not work on any optics ready Sigs. This red dot rear sight dovetail mount is easy to install and allows you to mount a red dot on your pistol without having to permanently modify the slide.

This mount does not work on any optics ready Sigs.

This mount fits (including but not limited to):
Sig Sauer P210A Standard
Sig Sauer P220
Sig Sauer P224
Sig Sauer P225
Sig Sauer P225-A1
Sig Sauer P226
Sig Sauer P227
Sig Sauer P228
Sig Sauer P229
Sig Sauer P238
Sig Sauer P239
Sig Sauer P245
Sig Sauer P320
Sig Sauer P938
Sig Sauer SP2022
Sig Sauer M11-A1
Sig Sauer MK25
Bersa Thunder UC Series (9/40/45)
Bersa Thunder HC Series (9/40/45)
FN 509
Sig Sauer #8 Sight Cuts

This mount does not fit:
Sig Sauer 1911s
Sig Sauer P220 10mm Hunter
Any Optics Ready Sig Sauer i.e. P226 Legion RX, P229 RX, P320 X-Carry etc.
Sig Sauer P210 Target
Sig Sauer P365 (The dovetail cut is too deep to work with our mount)
FN 509 Tactical

Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs

Mounting Hardware:
(2) 6-32 Button Head Screws
(2) 6-32 Flat Head Screws
(1) 6-32 Set Screw

Red Dot Fitment:
Vortex Viper
Vortex Venom
Burris Fast Fire 1, 2, 3, 4
Docter
ADE RD3-001
ADE RD3-002
ADE RD3-009
UTG Reflex Micro Dot
Crimson Trace CTS-1200
Crimson Trace CTS-1300
Sightmark Mini Shot

The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.

*All ADE mounts require 6-32 x 3/8" screws.

Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.