EGW Viper/Venom LPA Sight Mount

Mounting Hardware is Included

If you have a Para Elite LS Hunter or Remington R1 10mm Hunter you will need to select specific mount for the .

This mount fits (including but not limited to):
Sig Sauer 1911 Stainless Super Target*
Sig Sauer 1911 Match Elite*
Sig Sauer 1911 Target Full Size*
Sig Sauer 1911 Max Full Size*
STI with adjustable rear sights
STI Trojan
STI DVC 3 Gun
STI DVC Limited
STI DVC Classic
Springfield Range Officer
Springfield Range Officer Elite Target
Springfield Loaded Target
Rock Island TCM Rock Target FS HC Combo 22TCM / 9MM
Rock Island Pro Match ULtra 5” - 45 ACP
Rock Island Pro Match Tac Ultra 6” - 45 ACP
Rock Island Pro Match Ultra HC - 40S&W
Rock Island Pro Match Ultra 6” - 10MM
Rock Island Pro Match ULtra 6” HC - 10MM
Iver Johnson Eagle XL-SS10
Iver Johnson Eagle SS-10
Iver Johnson Eagle O.D. Green
Iver Johnson Eagle Coyote Tan
Iver Johnson Eagle XL-10 Ported
Iver Johnson Eagle XL-10
Iver Johnson Eagle XL-45 Ported
Iver Johnson Eagle XL-45acp
Iver Johnson Eagle LR

*We have found that some Sig Sauer 1911's with adjustable rear sights use a Kimber Adjustable style rear sight cut. Please measure the distance from the top of the front of the dovetail to the face of the sight cut in your slide. If this measures .43" you will need this (LPA) mount. If it measures .415" you will need the Kimber Adjustable.*

Please see our common 1911 dovetail chart if you are not sure which cut you have.

Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Minor modification may be neccessary for Rock Islands. Our products should be installed and checked by a qualified and competent gunsmith.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs

Mounting Hardware:
(2) 6-32 Button Head Screws
(2) 6-32 Flat Head Screws
(1) 6-32 Set Screw

Red Dot Fitment:
Vortex Viper
Vortex Venom
Burris Fast Fire 1, 2, 3, 4
Docter
ADE RD3-001
ADE RD3-002
ADE RD3-009
UTG Reflex Micro Dot
Crimson Trace CTS-1200
Crimson Trace CTS-1300
Sightmark Mini Shot

The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.

*All ADE mounts require 6-32 x 3/8" screws.

Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.