EGW DeltaPoint Pro Glock Sight Mount

Mounting Hardware is Included

This mount fits all generation Glocks with only rear sight dovetail cuts:
(including but not limited to)
Glock 17
Glock 17L
Glock 19
Glock 19x
Glock 20
Glock 21
Glock 22
Glock 23
Glock 24
Glock 26
Glock 27
Glock 29
Glock 30
Glock 30 SF
Glock 31
Glock 32
Glock 33
Glock 34
Glock 35
Glock 36 (Our mount is wider than the slide, but it will still work)
Glock 37
Glock 38
Glock 39
Glock 41
Glock 42 (Our mount is wider than the slide, but it will still work)
Glock 43 (Our mount is wider than the slide, but it will still work)
Glock 43x (Our mount is wider than the slide, but it will still work)
Glock 44
Glock 45
Glock 46
Glock 48 (Our mount is wider than the slide, but it will still work)
Canik TP9SF
Bersa BP9CC
Tactical Solutions .22lr Conversion
Advantage Arms .22lr Conversion

PSA Dagger (non-optics ready)

Does not fit ANY/ALL Glock MOS models.
Does not fit ANY/ALL Glock slides that are already cut for optics.

This mount will also fit the NON-optics ready PSA DAGGER

Our Glock sights are meant to be installed from the left to the right. The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.604"
Overall Width: .99"
Mounting Hardware: (2) 6-32 Button Head Screws, (1) 6-32 X 3/16 Set Screw
Red Dot Fitment:
Vortex Defender-CCW 3 MOA Red Dot Sight
Vortex Defender-CCW 6 MOA Red Dot Sight
Bushnell RXS-100 Requires 6-32 x 3/8" SHCS
Bushnell RXC-200 Requires 6-32 x 3/8" SHCS
Bushnell RXU-200 Requires 6-32 x 3/8" Flat Head Screws
Bushnell RXS-250 Requires 6-32 x 3/8" SHCS
Crimson Trace CTS-1500
Holosun 407K*
Holosun 507K*
Holosun EPS-GR*
Holosun EPS-RD*
Holosun EPS-Carry-GR*
Holosun EPS-Carry-RD*
Jpoint
Leupold Delta Point Pro
Optima
Redfield Accelerator
Shield RMS
Shield RMSc
Shield SMS
Sig Romeo Zero
(*with Modification, the rear two locater pins on the plate must be filed off in order to allow the 407K/507K/EPS Models to fit.)

Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.